process conditions
英 [ˈprəʊses kənˈdɪʃnz]
美 [ˈprɑːses kənˈdɪʃnz]
网络 工艺条件; 过程条件; 生产过程条件
双语例句
- Process conditions for the reforming section of an ammonia plant are optimized by process simulation.
采用过程模拟的方法对氨厂转化工序的工艺条件进行优化。 - Through investigation, the optimal solution formula and process conditions for low chromium white passivation technology are obtained.
通过研究低铬白色钝化工艺，得到了低铬钝化液的最佳配方及工艺条件。 - Impeller configuration is matched to the process conditions.
搅拌桨结构与工艺条件相匹配。 - Effect of shearing process conditions on the properties of SBS-modified asphalt
剪切工艺条件对SBS改性沥青性质的影响 - The second part of this work is to investigate the kinetics and mechanisms of the reaction between hydrogen chloride and calcium oxide to find out the optimal process conditions.
因此，本文第二部分工作研究了氯化氢和氧化钙反应的动力学及反应机理，以便找到最佳的工艺条件。 - Process conditions for methanolization and methanation purification of ammonia synthesis feed gas;
介绍了一种新的合成氨方法热平衡低温等离子体法。 - The formulation and process conditions of pre-treatment activating solution were presented.
给出了前处理活化液的配方和工艺条件。 - In this paper, we study the fermentation process conditions of fermented Jatropha cake ( meal) respectively by Geotrichum candidum and Candida utilis, and optimized the conditions.
本文研究了利用白地霉和产朊假丝酵母分别对麻疯树饼（粕）进行发酵的工艺条件，并对其工艺条件进行了优化。 - This paper introduces the basic principle and process conditions of single crystal silicon growth by Cz method.
介绍了直拉法生长单晶硅的基本原理及工艺条件。 - The influences of modified process conditions on the modification effect of cationic modifier on cotton fabric
改性工艺条件对阳离子改性剂在棉织物上改性效果的影响 - The loading of catalysts in layers and the process conditions are described for a three-stage Claus sulfur recovery unit.
介绍了三级克劳斯硫回收装置催化剂分层装填及工艺操作条件。 - Optimization of ISSR-PCR System for Lucuma nervosa by Using Orthogonal Design Through the study on the added amount of NaOH, reaction time and temperature, the optimum production process conditions were determined.
蛋黄果ISSR-PCR反应最佳体系的构建（简报）通过对氢氧化钠的加入量、应时间、应温度等生产条件的研究，得出了最佳生产工艺条件。 - The effect of process conditions, such as microwave, reactant ratio, catalyst and solvent etc, on the nucleophilic substitution and yield of product were investigated.
考察了微波技术、反应物料比、催化剂以及溶剂等主要条件对亲核取代反应和产物收率的影响。 - Effects of Variety of Liquid Crystals and Process Conditions on Pretilt Angle
液晶种类及工艺条件对预倾角的影响 - Pulping conditions of APMP using mixed hardwoods were studied in this paper, which mainly focused on the process conditions of pretreatment before refining.
本文对混合阔叶木APMP制浆工艺条件进行了探讨，着重研究了浸渍预处理各因素和打浆度对成浆质量的影响。 - The separation process conditions of caprolactam wastewater by manner of toluene is introduced, the purification process for salt in wastewater and the utilization technology for oil is indicated.
介绍了甲苯法生产己内酰胺废液的分离工艺条件、废液中盐的提纯和有机油的利用方法。 - This paper studied the synthesis process conditions of softener A-C, and found their optimum conditions.
本文对柔软剂A-C的合成工艺条件进行了探索和优化。 - The strength of the wool is not appreciably affected by carbonizing if the process conditions are carefully controlled.
如果碳化工艺做到了准确控制，羊毛的强度不会受到明显的影响。 - Two-component polyurethane adhesive for composite membrane was studied in terms of its composition, synthesis and process conditions.
本文确定了复合膜用双组份聚氨酯胶粘剂的组成成份，合成方法和工艺条件； - Through the study on the added amount of NaOH, reaction time and temperature, the optimum production process conditions were determined.
通过对氢氧化钠的加入量、应时间、应温度等生产条件的研究，得出了最佳生产工艺条件。 - Effects of composition in solution and process conditions on deposition rate were studied.
研究了镀液组成及操作条件对沉积速率的影响。 - In the article, the process conditions of wet surface modification of aphanitic graphite are studied.
选用不同的偶联剂对隐晶质石墨粉进行表面化学改性。 - Effects of each component content in solution, process conditions, power source on appearance of Sn deposit were studied by Hull Cell test.
通过赫尔槽试验研究了镀液中各成分含量、操作条件及电源对镀层外观的影响。 - Experimental Research on Treatment Process Conditions of Micro-polluted Source Water
微污染水源水处理工艺条件试验研究 - Manufacturer shall confirm compatibility of material of joint ring with the flange material and process conditions.
制造商应确定接合环材料与法兰材料以及工艺条件的兼容性。 - Objective To determine the molding process conditions of the medicinal carbon granules.
目的确定药用炭颗粒剂的成型（制粒）工艺条件。 - Selection of appropriate manufacturing method and process conditions.
成膜方法的选择及适合加工工艺的确定。 - Effects of process conditions on properties of deposit were studied.
研究了工艺条件对其镀层性能的影响。 - The process conditions of the start-up and stabilizing stage of rotating biological contactor are studied.
研究了生物转盘反应器启动阶段的工艺条件。 - The results showed that the glazed water permeable brick of high performance can be prepared under appropriate process conditions.
结果表明：在适当的工艺参数条件下，可以制备出高性能的釉面陶瓷透水砖。